Rectools yudo
  • OUTLINE
  • HOW TO

    • Contents 


    01.To think about before you start  

    • Because of radio waves the input might get noisy so please enable airplane-mode before you start.
    • Acoustic feedback might occur if you don’t use the speaker. Please use headphones or lower the speaker volume while the microphone is set to on.
    • Before you start RecTools02 make sure to connect any external devices that you plan to use and don’t unplug them until you are finished (it will result in a little delay since the audio system must be reinitialized). iPod touch users should not unplug any microphone external hardware cause the audio system can not be reinitialized after an such action, the application will still run but it not possible to play or record without doing a reboot).
    ▲ TOP

    02. The main screen. 

    1. PROJECT NAME  

    shows the name of the current project

    2. CLIP 

    Shows if the input is too loud

    3. WAVE / WAVE AREA 

    Shows the waveform of your recording.
    With one finger you can scroll this area with two fingers it’s also possible to zoom.

    4. TIME LINE 

    Shows the time at specific points in your projects.

    5. POSITION BAR / POSITION BAR CONTROL AREA  

    Shows where you are when playing or recording.(Information about the Control Area can be found in section 4)

    6. MARKER / MARKER AREA 

    Put markers on important places in your project and access them easily later.

    7. MARKER EDIT 

    Used when you add, move and delete markers.

    8. MARKER SEARCH 

    Moves you to the closest marker in a forward direction.

    9. TIME 

    Shows where the position bar is located in time.

    10. TRANSPORT 

    File, Recording and playback, wave editing, selecting
    ▲ TOP

    03.Lets make a recording! 

    1.Start the application

    Open RecTools01 from the home screen of your iPhone/iPod touch.
    (If you are using an external microphone make sure to connect it before you start the application)

    2.Create a new project

    Press FILE and a new window will appear. press NEW to create a new project.
    You can also load, change name, copy and delete projects in this window.

    3.Create a new project

    Enter a name and choose your settings.
    • NAME…The name of the project
    • AUDIO QUALITY…you can choose between 44.1kHz (Best) 22.05kHz(Ok) 11.025kHz (Worst).

    4.Recording

    Enable the microphone by pressing REC.
    Press REC to start to record.
    (Press on the recording button once again to enable SILENT KILL Silent kill mode)
    ▲ TOP

    04. Playback and the position bar 

    Playback

    press PLAY and the project will start playing from the position of the position bar.

    Change the position of the position bar

    Press inside the control area and move it freely.
    From the Transport:
    Goes to the start of the project
    Rewind
    Forward
    ▲ TOP

    05. Marker editing 

    Press once (press again to go back).
    This must always be done before you can start edit markers.
    The position bar’s control area will now be used for marker editing instead (marker area).

    Add markers:

    Press once inside the marker area to add a new marker

    Move markers:

    Press on the marker that you want to move and move it to the new position

    Delete markers

    Press on the marker that you want to delete and drag it in a upward direction, it gets darken and will be deleted once you
    release your finger.
    press to go to the next marker
    Note that it’s fully possible to move your finger to a different section of the screen (which makes it a lot easier to see cause your finger don’t cover the marker) once you have started a marker action.
    ▲ TOP

    06. Wave editing  

    To start edit your recorded wave blocks please press In RecTools02 you can MOVE, COPY, PASTE, DUPLICATE, DELETE, RESIZE and SPLIT your recorded wave blocks.
    With this set of features you can remove material that you don’t need and just keep the data that you want.
    For selection and moving of blocks you just have to touch the block that you want to edit.
    You can find a more detailed explanation of all the actions in the “08. The transport bar” section
    ▲ TOP

    07.PC SYNC 

    1. Project Mix Down

    Convert your entire project to one WAV file that can be played on your computer
    *To sync data to your computer you must first make a mix down of your project.

    2. PC Sync

    Via WI-FI you can download mix downs to your computer.
    * Your iPhone/iPod Touch must be in the same local network as your PC for this to work.

    ▲ TOP

    08. The transport bar 

    ■FILE MODE

    Press once and the following buttons will appear:
    Save the current project 
    Make a mix down of the current project.  
    Press twice and the following buttons will appear:
    You can create New projects, load previously saved projects, rename copy and delete projects. 
    Via WI-FI you can download mix downs to your computer.
    * Your iPhone/iPod Touch must be in the same local network as your PC for this to work. 

    ■REC & PLAY MODE

    Enable microphone input. 
    Goes to the start of the project  
    Rewind 
    Forward 
    Stops playback or recording. 
    Starts playback. 
    Start to record input from the microphone. 
    If you press on the recording button once again silent kill mode will be enabled. If no microphone input is present the application will stop automatically and when it is present again it will start.  

    ■EDIT MODE

    Press once and the following buttons will appear:
    Lets you make a multi selection.  
    Copy all the selected blocks. 
    Pastes all copied blocks. 
    Duplicates all selected blocks. 
    Delete all selected blocks. 
    undo actions (unlimited). 
    redo actions. 
    Press twice and the following buttons will appear:
    Changes the size of the block from the left. 
    Changes the size of the block from the right. 
    Split one block into two blocks. 
    ▲ TOP